220 Cm Sanforizing

NOMINAL WIDTH 2200mm
SUITABLE FOR WORKING FABRIC 1900mm WIDE
I. APPLICATION
IT IS SUITABLE FOR SANFORIZING VARIOUS WEAVING FABRICS OF PURE COTTON, POLYESTER-COTTON, CORDUROY, YARN DAMASK, COLOR WEAVING CLOTH AND FLAX TO IMPROVE THE FEEL, STEADY SIZE AND REDUCE THE SHRINKAGE.

II. PROCESS FLOW
INLET→MOISTURE→RUBBER BLANKET PRE-SHRINKAGE→FELT BLANKET FINISHER→COOLING DEVICE→DOFFING

III. MAIN SPECIFICATION
MACHINE HAND: LEFT OR RIGHT HAND
WIDTH: 2200mm
SPEED (M/MIN): 5~80M/MIN
PRESHRINKAGE: 16%, VARIED FROM VARIETY
SHRINKING RATE: ≤1%
STEAM PRESSURE OF PRESS ROLLER: 0.5MPA
DIAMETER OF DRYING CYLINDER OF FELT FINISH: Φ2000mm
FELT: ABOUT 2200G/M2
WATER CONSUMPTION (TON /HR): 1
STEAM CONSUMPTION (KG/HR): 500
TRANSMISSION AND CONTROL: PLC CONTROL, PARAMETERS ON LINE DISPLAY IN COLOR TOUCH SCREEN, MULTI-UNIT AC FREQUENCY CONVERSION DRIVE
INSTALLED POWER (KW): 38.45
OVERALL DIMENSION (L X W X H): 12010(L) X 4168(W) X 3925(H)mm

IV. MAIN STRUCTURE
THIS MACHINE IS MADE UP OF DAMPING MACHINE, PRE-SHRINKING MACHINE, FELT FINISHER.
1. DAMPING MACHINE:
(1) CONSTRUCTED WITH LOOSING FRAME, FEEDING ROLLER, STEAM DAMPING CYLINDER, CENTER ROLLER ETC.
(2) MOISTURE FOR THE FABRIC (STEAM SPRAYING) TO INCREASE THE SOFT AND SHRINKAGE BEFORE SANAFORIZER.
(3) THE STEAM DAMPING CYLINDER: DIAMETER ф570mm, STAINLESS STEEL, MAX. WORKING PRESSURE 0.3 MPA. CYLINDER WITH THE STRUCTURE OF WIRE SCREEN OUTSIDE AND THEN HEMP FRABRIC MAKE THE STEAM PENETRATE THE FABRIC DIRECTLY FOR THE NECESSARY MOISTURE RATE.

2. RUBBER BLANKET SHRINKING UNIT
(1) TO ELIMINATE THE MOST POTENTIAL SHRINKING STRESS IN THE FABRIC AND ACHIEVE THE SHRINKAGE PROCESS.
(3) DIAMETER OF SUPPORTING ROLLER φ616mm, IS MADE FROM STAINLESS STEEL, MAXIMUM PRESSURE 0.50MPA.
(4) PRESS ROLL, TENSION ROLL, GUIDE ROLL, WATER ROLL IS MADE FROM SEAMLESS STEEL TUBE WITH SURFACE CHROME PLATED.
(5) THE RUBBER BLANKET IS GRINDED BY GRINDING ROLL DRIVEN BY SEPARATED MOTOR.
(6) PRESS ROLL AND TENSION ROLL IS DRIVEN WITH SEPARATED MOTOR.

3. FELT FINISHING
(1) TO DRY THE FABRIC AFTER SANFORIZER AND KEEP THE SHRINKAGE EFFECT AND IMPROVE THE HAND FEELING.
(2) FELT BLANKET: 2200G/M2, WIDTH 2200mm
(3) THE DIAMETER OF THE BIG DRYING CYLINDER: φ2000mm, MATERIAL IS 20R CARBON STEEL AND THE MAXIMUM PRESSURE CAN REACH 0.5 MPA.
(4) THE DRYING CYLINDER: TOTAL 2 PIECES, THE DIAMETER φ570mm, MATERIAL IS STAINLESS STEEL AND THE MAXIMUM PRESSURE CAN REACH 0.4 MPA.
(5) CENTER ROLLER IS CONTROLLED BY PHOTOCELL SWITCH TO COLLECT THE FELT MOTION.

V. USER’S SCOPE
1. ENERGY SUCH AS WATER/POWER/AIR/STEAM ETC.
2. PIPELINES: THE PIPELINES BEYOND THE MACHINE FLANGE TO OUTSIDE IS SUPPLIED BY USER. THE FLANGE SPECIFICATION IS AS FOLLOWS:
STEAM PIPE: 2"
COMPRESSED AIR PIPE: 3/4"
WATER PIPE: 1 1/2"
3. COMPRESSED AIR: OUTPUT PRESSURE: 0.65-0.80MPA, OILLESS, WATERLESS, DUSTLESS. AVAILABLE FOR MACHINE CONNECTION.
REQUIREMENT FOR COMPRESSOR: VOLUME 1 M3, FLOW: 0.2 M3/MIN, DEW POINT: