Menu

B&G Plastic

Ref : 1723085-6-MT
Condition : Used
Manufacturer : B&G Plastic
Model : -
Year(s) : -
Quantity : 0
Location : Seller or machines location:
AMERICA North (USA-Canada-Mexico)
Last check : 10 Jan. 2020

1993 B&G Universal UWM-4 ^PET Stretch-Blow Molding Machine
* Features 4 Blow Molds for up to 1 Gallon (4 Liter) Containers
* Wide mouth capability!!!
PRICED RIGHT !!!

Combine this in-stock fully automated ^PET stretch blow molding line
with one of our in-stock fully automated preform manufacturing lines
for a fuuly automated ^PET resin to bottle manufacturing system:
- see our Husky XL300P complete preform manufacturing system, reference number 10077

SPECIFICATIONS OF THIS B&G STRETCH BLOW MOLDING LINE:

Preform Heater Section:
* Heater Length 64 inches, 1630 mm
(22 inches Condition and 40 inches Profile)
* Number of heating stations 17
* Equilibration length (No. of stations) 6-9
min.- max.(3.75* or 96 mm per station)
* Center distance between preforms 3.78 inches, 85 mm
* Center distance between lanes 8 inches, 152 mm
* Number of heater elements per bank 20
(one bank per preform lane)
* Total number temperature controlled zones (per bank) 20
Total per machine 60
* Total heater capacity 69KW
* Oven loading height 79 inches, +/- 0.3 inches
or 2005 mm +/- 10 mm
(from floor) with levalore in place
* Total number of pallets 33
* Total number of nose holders 132

Mold Unit:
* Platen and clamp specifications 88 tons
* Platen size (W & H) 24 x 16.38 inches, 610 x 415 mm
* Maximum daylight 13.50 inches
* Clamp Stroke (3.00 inches x 2) 6.00
* Bottom Stroke 3.0
* Mold Specifications:
Overall mold dimensions, each hull:
(W x H x D) 8 x 13.875 x 3.75 inches
Total mold thickness 7.5 inches
Mold bottom diameter, max (3 piece molds) 4.247 inches

Preform and Stretch Blown Container Data
(typical ranges only, do not use for preform design)
* Preform Specifications (.06 per side support ring recommended)
* Neck finish, min./max. 18 mm/89 mm
* Support ring diameter (max.) 3.82 inches
* Body diameter, min./max. 0.82 inches, 3.60 inches
* Overall length, max. 8 inches
* Maximum wall thickness 0.190 inches, 4.8 mm

Stretch Blown Container Specifications:
* Neck finish, min./max 18 mm/110 mm
(finishes larger than 89 mm are blown)
* Maximum diameter 6.75 inches
* Maximum height (w/o finish) 15 inches
* Approximate volume, max. 1 gallon, 4 liter

Power and Service Requirements:

Electrical:
* Power supply (volts/phase/cycle) 460/3/60
* Number of electric motors 6
* Total Rated H.P. 32
* Full load power requirements (controls, motors, heaters) 91KW

Hydraulic System
* Oil Reservoir capacity 120 gallons, 460 liters
* System pressure, max. 1000 psig, 70 kg/cm2

Cooling system Water
* Volume (min.) 0 temperature (max.) 25 gpm at 85 inches F
* Inlet and outlet connections 1-1/4 inches NPTF
* Auxillary mold chiller (mold and oven) 161,200 BTUH
* Inlet and outlet connections 1 inch NPTF
* Compressed air system - low pressure house air 100 psig
* System pressure, max. -- High pressure air 750 psig
* Inlet connection 2 inches NPTF

Typical Process Settings
(2-piece, 2-liter bottle, 2.7 sec.cycle)
(1-piece, 2-liter bottle, 3.5 sec cycle)
* Hydraulic system pressure 600 psig
* Compressed air pressure 450 psig/550psig
(min. recommend 20 percent increase)
* Compressed air volume, min 265 sc/m
(recommend 30 percent increase)
* Mold chilling water temperature +40 degrees F
* Volume and pressure 60 gal./min. at 80 psig

Typical Process for One Gallon (4 sec. Cycle)
* Water Temperature +40 degrees F
* Temp. Differential (in and out) 3 degrees F
* Compressed air volume 424 sc/m

Machine Dimensions Overall - Nominal
* Length 200 inches
* Width 109 inches
* Total ceiling height required 140 inches
* Total installation floor area 127 square feet
* Shipping weight 12 tons

Other machines similar to B&G Plastic

1
Location : EUROPE (Western and Northern)
Year(s) : 2016
1
Location : EUROPE (Western and Northern)
Year(s) : 2016
1
Location : EUROPE (Western and Northern)
Year(s) : 2011
1
Location : AMERICA North (USA-Canada-Mexico)
Year(s) : 2005