Used Others wood saw, cutters and trim

96" SOS (spout over shaft) 6 knife chipper Horizontal infeed Designed to produce quality chips from whole logs Year(s) : 1992 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

TWO (2) SAW HULA TRIMMER - Handles up to 6" thick to 12" wide x 20' long - Two (2) 7 - 1/2 HP belt driven 24" Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- Infeed Section - Right hand linebar (fixed) c/w idling rolls opposing each pressroll - Two (2) hydraulically Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- 8' to 24' lumber - Bar type unscrambler - Prepositioning infeed table - fed from the left c/w - Board turner Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- Multi rip saw - 12" wide x 3-1/2" thick x 30" minimum length - Model #312-DC - Slat bed feed - 50 HP arbor d Location : AMERICA North (USA-Canada-Mexico)

Price : On request

16FT THREE (3) SAW EDGER OPTIMZER - 1" to 4" thick x 4" to 24" wide x 6' to 16' long - Right Hand - USNR - Lu Location : AMERICA North (USA-Canada-Mexico)

Price : On request

60" Chipper - Drop feed, bottom discharge - 16 knife - c/w infeed chute (14" x 16") - 250 HP, 460 volt motor ( Year(s) : 1978 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

5' Cain Panel Rip Saw - Was removed from power May 10, 2007 to make way for a faster rip saw - Great roll-fed Year(s) : 2007 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

27" Debarker - LH - Left hand - Six (6) tool air seal ring - 100 HP ring drive motor - Feedworks drive - No ri Year(s) : 1995 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- Slat bed feed - 50 HP arbor drive motor, 440 volt - No shifting saws - Dismantled and ready to load Location : AMERICA North (USA-Canada-Mexico)

Price : On request

10" McGehee Shape Sawing Gang - Angled infeed rollcase (approx. 30' long) - Scan belt approx. 30" wide x 40' l Year(s) : 2002 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

VK 550 Combi 2R Debarker Logs up to 55 cm (75 cm max butt diameter) Feedspeed up to 120 m/min Flare removing r Year(s) : 1993 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

22" TANDEM RING DEBARKER - Right Hand - Frame Built in mid 90's - Air Seal rings - 1st ring built in 2001 and Year(s) : 2001 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

66" Chipper - Horizontal infeed - Bottom discharge - 8 knife - key knife conversion - No main arbor motor (dri Year(s) : 1977 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- 6" diameter to 36" diameter logs up to 20' long - Log stop and loader - Morbark Low mill style log turner - Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- Single sided - Digitally controlled - Very accurate - 575 volt Location : AMERICA North (USA-Canada-Mexico)

Price : On request

96" Chipper (Factory Rebuilt) - Rebuilt c/w 6 month new machine warranty - 96" - 8 knife, 7" disk, left hand - Location : AMERICA North (USA-Canada-Mexico)

Price : On request

27" DEBARKER - 105 FPM - Infeed and outfeed bed chains - Infeed and outfeed hourglass idling pressroll assembl Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Cooper Yield Champ Scragg - Up to 14" diameter - 36" to 60" in length - Infeed deck and log stop & loader - Lo Location : AMERICA North (USA-Canada-Mexico)

Price : On request

43" Disc Chipper - LH (spout under shaft - horizontal feed) - Maximum 10" diameter round - 4 knife - Built in Year(s) : 1999 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- 4" depth of cut - Saws set up as a pocket edger - Collared saws (5 saws in the edger) - No motor - Will do s Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Cambio Debarker c/w LSI Feedworks - 18" Cambio debarker ring - c/w individual hydraulic tool tensioning system Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Optimatic (Simonds) Model KRO970 Vertical Circle Saw Leveler - 150mm min. diameter, 810mm maximum saw diameter Year(s) : 2005 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

48" Chipper - Horizontal RH feed - Bottom discharge - c/w motor - All mounted on a common base - Vibrating con Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- 4" to 20" diameter (was set up for 14" diameter) - 8' to 20' length - Base feed speed 300 FPM @ 60 hz - Main Year(s) : 1999 Location : AMERICA North (USA-Canada-Mexico)

Price : On request