Used Wood Saws / Cutters

Finger Jointer - Model 3470 single chain machine with 575 volt electrics - 20 HP spindle motors x 1-13/16 bore Year(s) : 1988 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- Single sided - Digitally controlled - Very accurate - 575 volt Location : AMERICA North (USA-Canada-Mexico)

Price : On request

96" Chipper (Factory Rebuilt) - Rebuilt c/w 6 month new machine warranty - 96" - 8 knife, 7" disk, left hand - Location : AMERICA North (USA-Canada-Mexico)

Price : On request

27" DEBARKER - 105 FPM - Infeed and outfeed bed chains - Infeed and outfeed hourglass idling pressroll assembl Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Cooper Yield Champ Scragg - Up to 14" diameter - 36" to 60" in length - Infeed deck and log stop & loader - Lo Location : AMERICA North (USA-Canada-Mexico)

Price : On request

43" Disc Chipper - LH (spout under shaft - horizontal feed) - Maximum 10" diameter round - 4 knife - Built in Year(s) : 1999 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- 4" depth of cut - Saws set up as a pocket edger - Collared saws (5 saws in the edger) - No motor - Will do s Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Cambio Debarker c/w LSI Feedworks - 18" Cambio debarker ring - c/w individual hydraulic tool tensioning system Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Complete 16' Sawmill and Planermill Sawmill - 8' - 16', up to 24" diameter - Large log side - #1 long log infe Year(s) : 2007 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Optimatic (Simonds) Model KRO970 Vertical Circle Saw Leveler - 150mm min. diameter, 810mm maximum saw diameter Year(s) : 2005 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

48" Chipper - Horizontal RH feed - Bottom discharge - c/w motor - All mounted on a common base - Vibrating con Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- 4" to 20" diameter (was set up for 14" diameter) - 8' to 20' length - Base feed speed 300 FPM @ 60 hz - Main Year(s) : 1999 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

24 ft - Log Ladder - 4 steps - 8' to 24', 4" to 30" diameter - up to 20 cycles per minute - Even ending rollca Year(s) : 2002 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- Up to 20" diameter capacity - Diesel powered - Dual vertical chain flail - Flail debarker 23" x 55" opening Location : AMERICA North (USA-Canada-Mexico)

Price : On request

ForestPro Debarking System Flail - 23" capacity - Hydraulically gear box driven dual horizontal chain flails Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- 36" x 50" wide inlet - 200 HP motor 480/3/60 - No bottom screen - Capacity up to 25 tons per hour Year(s) : 1973 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

48" Chipper - 4 knife - Horizontal in - Bottom out - 100 HP, Toshiba high efficiency, 1800 RPM, 460 volt (not Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- Opening is 56" wide x 60" long - 900 HP @ 2300 Volt, 3 phase, 60 hertz - Twenty (20) hammers, weight approx. Location : AMERICA North (USA-Canada-Mexico)

Price : On request

12" Debarker (RH) - Built in 1995 (in service 1996) - 2" diameter to 12" diameter - 283 FPM - Air cell - Four Year(s) : 1995 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

116" Chipper - 30" maximum diameter - Horizontal infeed / bottom discharge - Twelve (12) knife c/w replaceable Year(s) : 1991 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

Mill Tech PET Trimmer Transfer & Trimmer Transfer: - 25 HP drive.(VFD not included here) - Approx. 17-0" shaf Location : AMERICA North (USA-Canada-Mexico)

Price : On request

6' Air Strain Double Column Twin Bandmill - 11-1/4" wide wheels with upper wheels measuring 7/8" at edge and Year(s) : 1986 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- 2 side heads - 4 front knives on each head - 4 side knives on each head - Feed modules Location : AMERICA North (USA-Canada-Mexico)

Price : On request

- Built in 1996 (only ran 7 months from new) - 27" maximum log diameter - Right Hand - Horizontal feed, bottom Year(s) : 1996 Location : AMERICA North (USA-Canada-Mexico)

Price : On request

KRUSI AUTOMATIC LOG MILLING MACHINE - capable of milling dovetails, lap joints, joinery, end cuts, key cuts an Year(s) : 2008 Location : AMERICA North (USA-Canada-Mexico)

Price : On request